Description
50V 0.22µF radial electrolytic capacitor, XXS standard series, 2,000 hours at +105 °C. Ratings this small appear in signal paths and low-current rails where a ceramic would be marginal on capacitance tolerance or where a wet part is simply what the existing design already uses.
Low-Temperature Behaviour at -40 °C
At 50 V the specified impedance ratio Z(-25 °C)/Z(+20 °C) is 2 at 120 Hz. The series also specifies Z(-40 °C)/Z(+20 °C) = 4, which applies here because this voltage rating sits inside the -40 °C to +105 °C band.
An impedance ratio of 2 means the part looks roughly 2 times more resistive at the cold extreme, so at 120 Hz its effective capacitance is about 0.11µF at -25 °C. If the equipment has to start cold and still meet a ripple or hold-up target, size against that reduced figure rather than the room-temperature value.
Ripple Current and Internal Heating
The heat a capacitor generates is the ripple current squared times its equivalent series resistance. The catalogue does not publish ESR as a separate column for this series; it is derived from the dissipation factor, and at 50 V / 0.22µF the specified tanδ of 0.12 at 120 Hz works out to roughly 723.43 Ω of series resistance.
Dissipation at the 3 mA rating is roughly 6.5 mW, which the Ø5 × 11 mm can has to shed. The 2,000-hour figure is the life at +105 °C with that ripple applied continuously — a lower ambient temperature buys back life quickly.
Footprint, Lead Spacing and Insertion
The Ø5 × 11 mm case uses a 2 mm lead pitch with 0.5 mm lead diameter, the standard radial grid for this body size. Board layout should allow for the lead taper and for a small clearance under the can so the sleeve is not pinched against the substrate.
The negative lead is the short one and the sleeve carries the polarity stripe. Since the aluminium can is not insulated, check the creepage to any nearby chassis metal before tightening the layout.
Reading the 2,000-Hour Rating Correctly
The 2,000 hours printed on the sleeve is measured at the full +105 °C with rated ripple applied for the whole test. A cabinet running at 55 °C is not the same thing, and treating the two as equivalent is the most common way designers over-estimate electrolytic life.
The usual halving rule applies: each 10 °C drop in core temperature roughly doubles the life. A 2,000-hour part running 40 °C below its rating is in the tens of thousands of hours, which is why the XXS series is still specified into equipment with a normal service life. The catalogue itself notes the series covers 2,000 to 3,000 hours depending on case size, with the larger cans reaching the longer figure.
Specifications
| Item | Characteristics |
|---|
| Rated Voltage | 50 V |
| Nominal Capacitance | 0.22 µF ±20% (M) |
| Case Size (ØD × L) | Ø5 × 11 mm |
| Operating Temperature Range | -40 °C to +105 °C |
| Endurance | 2000 hours at +105 °C with rated ripple |
| Rated Ripple Current | 3 mA rms at 120 Hz, +105 °C |
| Dissipation Factor (tanδ) | 0.12 max. at 20 °C, 120 Hz |
| Low Temperature Impedance Ratio | Z(-25 °C)/Z(+20 °C) = 2, Z(-40 °C)/Z(+20 °C) = 4 |
| Leakage Current | I ≤ 0.01CV or 3 µA (20 °C, 2 min) |
| Lead Pitch (P) | 2 mm |
| Lead Diameter (d) | 0.5 mm |
| Terminal Type | Radial, 2-pin, through-hole |
Where This Rating Is Used
- local bypass next to a logic device
- timing networks where a stable RC constant matters
- signal coupling between amplifier stages
The XXS series is specified for communication equipment, switching power supplies, industrial measuring instruments and automotive electric products — the applications the catalogue lists for the range. For 50 V at 0.22µF the three above are the positions this rating most often fills.
The 2,000-hour class is the entry point. For a longer service life in a similar Ø5 mm can, look at the XLS and XLL series in the radial electrolytic capacitor range.
Product Details
- Two-lead radial package with a 2 mm pitch, matching the board footprint convention for a Ø5 mm can
- Printed sleeve carrying the voltage and capacitance marking, with the polarity band on the negative side
- Safety vent on the case top for pressure relief under fault conditions
- Supplied in bulk or on tape and reel depending on case size

Production Workshop
Radial production at Xuansn runs in Dongguan, where this 50 V / 0.22 µF rating is wound, impregnated, aged and tested before packing. Each batch goes through automated element winding, vacuum electrolyte impregnation, high-temperature voltage aging, and 100% electrical screening for capacitance, tanδ and leakage current before packing.


Certifications
ISO 9001 and ISO 14001 certification covers the Dongguan plant, and the capacitor range is supplied to RoHS and REACH. The 50 V 0.22 µF part is 100% screened for the three electrical parameters listed in the specification table.

Frequently Asked Questions
What service life should I expect from this rating?
2,000 hours is quoted at +105 °C with the full 3 mA ripple applied. Running the Ø5 × 11 mm can cooler than that — 65 °C instead of 105 °C — multiplies the figure by roughly sixteen under the standard halving rule. Give us the cabinet temperature and the ripple waveform and we will work it out for your case.
What is the minimum order quantity?
MOQ depends on the case size — a Ø5 mm can runs in larger quantities per batch than the small diameters. Send the annual figure for this 50 V / 0.22 µF rating and we will quote to it.
Can the sleeve be printed with our own marking?
Custom marking is available on the Ø5 × 11 mm sleeve. Supply the artwork at print resolution and we will return a proof showing the printable area for this case diameter before the run starts.
I have an existing part number — can you match it?
Yes. Send the current part number and the operating conditions — voltage, ripple, ambient, and the space available on the board — and we will propose the closest XXS rating with the case size comparison.
Contact
Need a datasheet, ESR data at 100 kHz, or samples for this case size? Contact the Xuansn engineering team:
✉ coco@xuanxcapacitors.com | ☎ +86-18825879082 | Request Technical Support & Samples